Skip to content
Need help identifying a part? Contact parts support
SKU: 6410Brand: Non-Specified Brand
,

2 inch x 48 inch Galvanized Steel Nipple

$14.67

2″ x 48″ Galvanized Steel Nipple – Schedule 40, Threaded Both Ends The 2″ x 48″ Galvanized Steel Nipple is a Schedule 40 straight pipe fitting used to extend, connect, or transition between two female-threaded components in mechanical and plumbing systems.

Quantity

2″ x 48″ Galvanized Steel Nipple – Schedule 40, Threaded Both Ends

The2″ x 48″ Galvanized Steel Nippleis a Schedule 40 straight pipe fitting used to extend, connect, or transition between two female-threaded components in mechanical and plumbing systems. Constructed from carbon steel and hot-dip galvanized to ASTM A123/A153 standards, this nipple is designed to provide durable, corrosion-resistant performance in non-potable water, air, oil, and other approved fluid applications.

Threaded on both ends per ANSI B1.20.1 (NPT), this fitting enables secure mechanical joints in systems subject to moderate pressure and temperature variations. Galvanized coating extends service life by resisting rust and environmental degradation in exposed or damp conditions.

Technical Specifications

  • MaterialCarbon steel with hot-dip galvanized finish
  • Nominal Pipe Size2 inches
  • Length48 inches (end-to-end)
  • Connection TypeNPT male x NPT male
  • Wall ThicknessSchedule 40
  • StandardsASTM A733 (nipple fabrication), ASTM A53 Grade A/B (pipe), ANSI B1.20.1 (threads)

Application Scope

This galvanized steel nipple is intended for use in threaded pipe systems that require corrosion resistance and structural integrity. Common installation areas include

  • ✅ Water distribution in non-potable systems
  • ✅ Compressed air and pneumatic lines
  • ✅ Outdoor irrigation and washdown infrastructure
  • ✅ Low-pressure industrial fluid transfer
  • ✅ Support extensions in pipe hangers and structural conduit routing

Installation Considerations

Install using pipe wrenches and apply an appropriate thread sealant (PTFE tape or pipe joint compound) to achieve a pressure-tight seal. Ensure that threads are clean, properly aligned, and fully engaged. Do not overtighten, as excessive torque can deform threads or cause joint failure. This nipple is not intended for pressurized potable water unless certified for such use.

Key Performance Features

  • ✅Hot-Dip Galvanized CoatingProtects steel substrate from corrosion in moisture-prone environments
  • ✅Long-Length FormatProvides extended reach without the need for multiple fittings or unions
  • ✅Threaded EndsNPT threading ensures compatibility with standard pipe fittings
  • ✅High Mechanical StrengthCarbon steel body supports system loads and pressure requirements

Code & Compliance Note

This product is manufactured in accordance with applicable ASTM and ASME standards for non-potable water and mechanical piping systems. It should be installed in compliance with local plumbing and mechanical codes. For systems requiring NSF 61/372 certification, verify component approval with the project specifications or AHJ.

The2″ x 48″ Galvanized Steel Nippledelivers durable, long-length connectivity for industrial, mechanical, and commercial-grade piping systems. Its corrosion-resistant coating and precise threading make it a dependable solution for pipe extension and system integration across a range of applications.

Specifications

Specifications Weight 14.600000 Brand Non-Specified Brand ADA Compliance No Length (inches) 48 Width (inches) 2 Height (inches) 2 Side A 2″ Side B 48″ Fitting Type Nipples Item Type Fittings Manufacturer Non Specified Manufacturer MPN 568-480HC Material Galvanized Steel Product Family Fittings Item Returns This item can be returned

Buying Information

Confirm the listed size and connection details for MPN 568-480HC before ordering.

Brand

Non-Specified Brand

MPN

568-480HC

0
Scroll to Top