Skip to content
Need help identifying a part? Contact parts support
SKU: 102257Brand: Non-Specified Brand
,

6 inch x 4 inch PVC Sewer and Drain Reducing Coupling Hub x Hub

$10.63

P658 S&D Coupling – 6 inch x 4 inch Hub x Hub Transition Fitting for Sewer and DWV Systems The P658 S&D Coupling SWR H x DWV H 6 inch x 4 inch is a solvent-weld transition fitting used to connect 6-inch sewer pipe to 4-inch DWV (Drain, Waste, and Vent) pipe.

Quantity
SKU: 102257 Categories: ,

P658 S&D Coupling – 6 inch x 4 inch Hub x Hub Transition Fitting for Sewer and DWV Systems

The P658 S&D Coupling SWR H x DWV H 6 inch x 4 inch is a solvent-weld transition fitting used to connect 6-inch sewer pipe to 4-inch DWV (Drain, Waste, and Vent) pipe. Designed for non-pressurized systems, this coupling provides a reliable solution for joining dissimilar pipe diameters in sanitary drainage and stormwater applications.

Manufactured to ASTM and applicable municipal standards, this PVC coupling accommodates standard SDR 35 (Sewer) and ASTM D2665 (DWV) pipe dimensions. Its dual-hub configuration allows for solvent welding on both ends using approved primers and cements, ensuring a permanent, watertight seal in underground and above-grade installations.

Product Attributes

  • ✅MaterialInjection-molded PVC, engineered for durability and chemical resistance in buried and above-ground drainage systems.
  • ✅Connection TypeHub x Hub (Socket x Socket) solvent weld ends, sized to fit 6 inch SDR 35 and 4 inch DWV pipe.
  • ✅Application RangeTransition fitting for gravity sewer mains, residential lateral lines, and commercial DWV tie-ins.
  • ✅Operating PressureRated for non-pressurized systems; tested under ASTM D3034 and D2665 for structural integrity and infiltration resistance.
  • ✅Size Compatibility6-inch x 4-inch nominal dimensions; suitable for step-down connections in new or retrofitted drainage systems.

Installation Requirements

Prior to installation, pipe ends must be chamfered and cleaned using CPVC/PVC-compatible primer. Apply solvent cement to both hub and spigot ends and insert fully to bottom-out depth. Allow proper set and cure time before backfilling or testing. All installation procedures must comply with local plumbing codes, and proper bedding is required in below-grade applications to prevent misalignment or joint stress.

Typical Use Cases

This coupling is used in stormwater drainage, municipal sanitary sewers, and DWV systems where a step-down transition from 6 inch to 4 inch is required. It is especially useful in residential and light commercial construction for lateral tie-ins, cleanout branches, and system modifications involving existing infrastructure.

Code & Compliance Note

Fittings used in gravity-flow DWV and S&D (Sewer & Drain) systems must meet dimensional and performance requirements outlined in ASTM D3034 (Sewer) and ASTM D2665 (DWV). This product meets those standards when properly installed and is approved for use in UPC and IPC jurisdictions.

Technical Specifications

  • Nominal Size6 inch x 4 inch
  • Fitting TypeSewer x DWV Reducing Coupling
  • MaterialPVC, per ASTM D1784 (Cell Class 12454)
  • Connection MethodSolvent weld (hub x hub)
  • StandardsASTM D3034 (Sewer), ASTM D2665 (DWV), NSF-listed for wastewater use

Specifications

Specifications Weight 1.040000 Brand Non-Specified Brand ADA Compliance No Length (inches) 2.88 Width (inches) 6 Height (inches) 2.88 End Style Hub x Hub Side A 6″ Side B 6″ Fitting Type Coupling Item Type Fittings Manufacturer Non Specified Manufacturer MPN P658 Material PVC S&D Product Family Fittings Item Returns This item can be returned

Buying Information

Confirm the listed coupling configuration and MPN before ordering.

Brand

Non-Specified Brand

MPN

P658

0
Scroll to Top