Skip to content
Need help identifying a part? Contact parts support
SKU: 2010917Brand: LukjanAvailability: Out of Stock
,

8″ Smoke Chimney Cap

$6.52

Lukjan Non-Adjustable Rain Cap — Series 47, Ø 8″, 9-1/2″ Length × 12-1/2″ Width Fixed (non-adjustable) rain / vent cap intended for 8-inch round duct or flue terminations. The Series 47 rain cap provides weather protection without moving parts, with a generous hood and skirt to sh…

Out of stock

SKU: 2010917 Categories: ,

Lukjan Non-Adjustable Rain Cap — Series 47, Ø 8″, 9-1/2″ Length × 12-1/2″ Width

Fixed (non-adjustable) rain / vent cap intended for 8-inch round duct or flue terminations. The Series 47 rain cap provides weather protection without moving parts, with a generous hood and skirt to shield the duct opening from precipitation, debris, and pests.

  • Series / modelSeries 47non-adjustable rain / chimney cap (Lukjan):contentReference[oaicite:1]{index=1}
  • Nominal duct connection8 inches diameter (round duct / flue)contentReference[oaicite:2]{index=2}
  • Overall depth / projection (front-to-back)9-1/2 inches (9.50″)contentReference[oaicite:3]{index=3}
  • Overall brim / hood width12-1/2 inches (12.50″)contentReference[oaicite:4]{index=4}
  • Material: Galvanized steel (standard for Lukjan sheet metal vent caps)
  • Finish: Galvanized coating (zinc) to resist rust and outdoor exposure
  • Weight: ~0.50 lb (typical for the corresponding 8″ cap model):contentReference[oaicite:5]{index=5}
  • Design features
    • Non-adjustable (fixed hood) — no sliding or movable parts.
    • Wide hood / brim helps deflect rain and snow away from the duct inlet.
    • Vertical skirt or side walls to minimize wind-driven water entry.
    • Edge hems or flanges (where present) stiffen the hood edges and reduce sharpness (common in metal vent caps).
  • Installation / mounting
    • Slip or bolt the cap over the duct / chimney pipe end, ensuring full seating over the termination.
    • Secure with corrosion-resistant sheet-metal screws or fasteners via skirt flanges or optional brackets.
    • Seal at the base between the duct and the cap (using high-quality exterior sealant or flashing) to prevent water infiltration.
    • Mount level, stable, and plumb — avoid tilt or misalignment that could compromise performance or cause stress under wind load.
  • Performance & design considerations
    • The 12-1/2″ brim width relative to the 8″ duct gives a generous overhang, helping to minimize rain entry even under angled wind conditions.
    • The 9.5″ depth ensures vertical spacing so water drips past the duct opening rather than splashes inward.
    • Because it is fixed, no mechanisms reduce maintenance complexity or points of failure.
    • In more corrosive or coastal environments, optional stainless steel or painted finishes might be preferable for longevity.
  • Limitations & notes
    • As a non-adjustable cap, it may not adapt well if duct termination heights vary — precise installation is important.
    • Debris, leaves, or bird nests may accumulate under the brim — periodic inspection and cleaning are recommended.
    • Sufficient clearance to surrounding structure should be maintained so that the hood does not impinge on walls, soffits, or overhangs.

Specifications

Specifications Weight 0.500000 Length (inches) 14 Width (inches) 14 Height (inches) 9 Item Type HVAC Duct Brand Lukjan Inclusions/Features Done Manufacturer Lukjan Metal Products MPN RX2808 Sub Type Rain Cap Diameter 8 in Shape Round Item Returns This item can be returned

Buying Information

Match RX2808 to the existing component before ordering

Brand

Lukjan

MPN

RX2808

0
Scroll to Top